Anyone for "CHIPS" with that? ;)

Posts

Post 247593 by Johnny5 on 2009-08-05 22:27:27

Well its been a while, and the 850 is still going strong! I need some help, I have ordered a replacement chip for the engine ecu ;) However....... Im pretty good at soldering usually, But this is a different animal! Opened up the ecu and hey presto theres the chip sitting there in all its SOLDERED glory on the board, with me and tears in my eyes from straining to see the soldered joints on the other side! lol..... Has anyone else had a go at soldering one of these in?????? Or does anyone know who would do it for me???????? (For a reasonable price ofcourse!) Your help is appreciated as always ladies n gents! John

Post 247614 by Torch S70R on 2009-08-05 23:46:30

i take it that its a through hole chip m8? ie the legs protrude through the other side of the pcb we do a lot of surface mount soldering at work and through hole is just a walk in the park in comparison, I could certainly change it for you if you like

Post 247619 by AlanG on 2009-08-06 00:32:39

What did this cost you bud? And also,what guarantee do you have of a safe improvement? Have you checked into Hamish's site?? http/www.hlmtuning.co.uk/offers/dtml

Post 247658 by Alan M on 2009-08-06 10:32:54

IF ou do go ahead with the chip replacement you could go to an electronics specialist and get a price off them for fittng as they should have the necessary deoldering equipment to remove then refit the new item.

Post 247659 by thebadger on 2009-08-06 10:47:37

New chip for my ME7 ECU was £7. But that's a surface mount chip...

Post 248065 by Johnny5 on 2009-08-07 20:04:49

Gents, Its a hole through chip, from good ole e-bay! Comes direct from Germany and cos me £105 including postage, claiming to increase the BHP to 310 with 460NM torque on a stock engine, howver mine has a free flow S/S exhaust so im hoping for 330bhp ish..... Item link is http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250472643388&ssPageName=STRK:MEWNX:IT I have contacted other buyers of the chip and they all say its made a huge improvement to power and driveability...... Lets wait and see eh........... More to follow when the chip arrives lol ;)

Post 248070 by danny-R on 2009-08-07 20:15:44

you're a braver man than i am mate. no way on earth would i trust a lithuanian seller with only 12 feedback and none of these feedback comments are for a volvo chip. dont get me wrong i'm not sayin it won't work, just what you've paid i personally would have gone down the rica route. good luck with it tho

Post 248072 by walter leever on 2009-08-07 20:19:37

First of all,as said you're a brave man.:bounce: Secondly don't get fixed on those numbers,you will have to do a lot more to get 330 bhp than just a chip and a freeflow exhaust.:shhh:

Post 248073 by Johnny5 on 2009-08-07 20:20:02

couldnt afford rica m8 :( Theyre located in germany, and i have contacted people who have bought from them and all seems good, been in contact with a lady from austrailia who has got one, and she seems well happy with it, so im hedging my bets that its ok... Lets see what happens ;) anyway if its no good, ive seen plenty of spare ecu's on e-bay! lol

Post 248074 by Tomcat on 2009-08-07 20:20:09

Although the supplier of the chip may be reputable I'd be vary cautious, at least get a socket fitted to your ecu, that way if the new chip turns out to be a piece of crap you can just swap it out for the original one. You will not see 310bhp from a chip alone, especialy on an 850 that's done plenty of miles. Mine has an ecu uprgade that's supposed to give 305bhp and even with a k&n and a decent cat back exaust system it's only producing 267bhp at the wheels. All that said, good luck and I hope it gives a decent power increase for you.

Post 248079 by Johnny5 on 2009-08-07 20:33:05

Tomcat -- I was thinking of doing that socket job 1st anyway, so that if it is crap i can change it back to the standard chip, was also thinking if it was good then having some kind of piggy-back method of switching the car from standard tune to performance, much like my old VXR zafira had with the "sports" mode button! ;)

Post 248080 by danny-R on 2009-08-07 20:33:18

by rica, i meant the £150 ecu upgrade offer from hlm (hamish). thats what i got 6 months ago and i am more than happy with it.

Post 248082 by Johnny5 on 2009-08-07 20:39:44

Wasnt aware that they were so cheap! :( oh well, money is spent now..... So lets hope its all good or they gonna get bad feedback and a claim through paypal hehe ;)

Post 248087 by danny-R on 2009-08-07 20:52:44

well good luck with it and do keep everyone informed of how it goes for future reference.

Post 248098 by Johnny5 on 2009-08-07 21:50:53

Dont worry, plenty of updates coming your way guys..... lol

Post 248103 by AlanG on 2009-08-07 22:11:43

Good luck wi that Johnny..310BHP from a chip is going one of 2 ways...A couple of hours of ruling the land of speed,then total destruction or it's hokum. I don't believe for a minute that a chip can add 85bhp. Be careful mate and I wish you well.

Post 248105 by Johnny5 on 2009-08-07 22:18:06

My "boy racer" days are long gone, spent many a happy hour blasting up and down the streets of Brighton in my Sapphire cosworths and my RS turbo's etc etc etc , just want that little extra when its needed and some better driveability.... We shall see whjat happens, im not expecting to get 85BHP just from a re-mapped chip.... But its a start! j

Post 248117 by AlanG on 2009-08-07 22:41:53

That's fair buddy,think we've all been there....Had a few myself,Rover V8 SD1s man and auto,18 years old at the time (my mum was very acommodating ins wise) and ultimately a 230bhp XR4x4 Turbo Technics. Very fast and very,very,very thirsty. Did you look on Hamish's site?

Post 248265 by Johnny5 on 2009-08-08 17:05:29

Always wanted (and still do) an Escort cossie, but could never afford one, and still cant! Theyre still fetching silly money, even at auction! Anyways I havnt had a chance to look on hamish's site as yet but i will when i get the chance... cheers

Post 248273 by Jod T5 on 2009-08-08 17:16:49

[quote=Johnny5;248105]My "boy racer" days are long gone, spent many a happy hour blasting up and down the streets of Brighton in my Sapphire cosworths and my RS turbo's etc etc etc , just want that little extra when its needed and some better driveability.... We shall see whjat happens, im not expecting to get 85BHP just from a re-mapped chip.... But its a start! j[/quote] You may well get 85 brake increase.... What you have to realize is that a stock 850 T5 is more likely to be kicking 180 brake at stock rather than 225... This is due to ageing of external components such as BCS, actuator and Vacuum pipe work... Jod

Post 248283 by Johnny5 on 2009-08-08 18:27:49

True, very true!

Post 248284 by AlanG on 2009-08-08 18:27:52

Well using your thinking Jod,if that be the case then any expected increase will be lower as it will accentuate these weaknesses,

Post 248821 by Johnny5 on 2009-08-11 22:03:31

Hmmmmmmm no sign of the chip as yet :( not worried so far as other have waited 10 - 12 days for delivery. its only been 7 for me so far! ;)

Post 248830 by p fandango on 2009-08-11 22:32:53

[quote=Johnny5;248821]Hmmmmmmm no sign of the chip as yet :( not worried so far as other have waited 10 - 12 days for delivery. its only been 7 for me so far! ;)[/quote] hope they haven't done the same thing as the company/chap selling the bonnet pins i brought off ebay. Should of been sent out first class so was expecting them yesterday but no sign of them, went & had another look at the advert to make sure i wasn't rushing it, & after i'd brought & paid for them he's gone on & put a message saying he's going off on his hols now till the 31st & everything will be sent when he gets back :splat:

Post 249167 by Johnny5 on 2009-08-13 23:11:24

:mad: ARRRRRRRRRRRRGGGGGGGGGGGGGGHHHHHHHHHHHHHHHHHHHHH! Well the chip arrived today YAY! with full fitting instructions, so i promptly went about un-soldering the original chip and soldering in the new one! All good so far! But........................... Now it wont start, and the cooling fan is on all the time! GRRRRRRRRRRRRRRRRRRRRR Help anyone? Also, anyone breaking a 1994 T5 Auto who would sell me a spare engine ecu so I can use the car while i investiagte why the damn thing wont start! Plz txt or call me 07817 340943

Post 249208 by 850 2.5 10v on 2009-08-14 09:25:19

Remove it immediately, put it in the bin, then call Hamish at HLM. Put the whole thing down to experience. You could cause more damage trying to fiddle with it. Its just not worth it - leave it to the experts.

Post 249212 by RollingThunder on 2009-08-14 09:38:34

I saw the eBay ad too, but decided against it - Lithuania is too far to go to make a 'forceful' complaint. And they tend to have big burly 'security' personnel :) I was in Estonia a while back and believe me, guns are readily for hire :D Stick with RICA or MTE - they're reputable and won't have dubious/dangerous maps. In the meantime, don't drive the car with that chip in it...

Post 249213 by MIKESC70T5 on 2009-08-14 09:45:38

[quote=RollingThunder;249212]I saw the eBay ad too, but decided against it - Lithuania is too far to go to make a 'forceful' complaint. And they tend to have big burly 'security' personnel :) I was in Estonia a while back and believe me, guns are readily for hire :D Stick with RICA or MTE - they're reputable and won't have dubious/dangerous maps. In the meantime, don't drive the car with that chip in it...[/quote] Can't drive it with that chip in, it won't start :slap:

Post 249224 by smudgethecat on 2009-08-14 10:29:18

[quote=Johnny5;248065]Gents, Its a hole through chip, from good ole e-bay! Comes direct from Germany and cos me £105 including postage, claiming to increase the BHP to 310 with 460NM torque on a stock engine, howver mine has a free flow S/S exhaust so im hoping for 330bhp ish..... Item link is http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250472643388&ssPageName=STRK:MEWNX:IT I have contacted other buyers of the chip and they all say its made a huge improvement to power and driveability...... Lets wait and see eh........... More to follow when the chip arrives lol ;)[/quote] 330bhp? keep taking the tablets mate

Post 251005 by Johnny5 on 2009-08-22 21:53:25

@@@@@@@@@@@@@@@ UPDATE @@@@@@@@@@@@@@@@@ anyone fancy having a go at this chip for me????? I have been today to the local breakers and got another ecu from a T5 for £20.... Slotted it in and it starts and runs fine! YAY! The one with the re-mapped chip in is here on my desk, all seems ok on the board nothing untoward to the naked eye????? But in the car it causes the cooling fan to run all the time and the engine wont start (not even a glimmer ) Theres gotta be someone out there who fancies a go at sorting it for me, dont wanna throw the ecu away for summat simple that i may be missing! J

Post 251010 by Tomcat on 2009-08-22 21:56:36

Stupid question I know....but you have put the chip in the right way around haven't you?..

Post 251016 by Johnny5 on 2009-08-22 22:08:33

Well its not a stupid question as all help is greatly appreciated, i was going by the small semi circle cut out in the chips body as the marker for its position on the board, replacing like for like if you know where im coming from, the replacment chip has only 28 legs whereas the original one has 32, the instructions state that this is the EWS II ecu type, stating also that the EWS immobiliser will not function???? (Im guessing that this is referring to a "transponder type" key system which the T5 doesnt have???

Post 251022 by AlanG on 2009-08-22 22:22:57

As someone has said mate........Chuck it in the bin and call Hamish.

Post 251023 by Johnny5 on 2009-08-22 22:25:12

Dont think so alan, cant throw away £100 ;)

Post 251026 by walter leever on 2009-08-22 22:28:54

[quote=Johnny5;251016]Well its not a stupid question as all help is greatly appreciated, i was going by the small semi circle cut out in the chips body as the marker for its position on the board, replacing like for like if you know where im coming from, the replacment chip has only 28 legs whereas the original one has 32, the instructions state that this is the EWS II ecu type, stating also that the EWS immobiliser will not function???? (Im guessing that this is referring to a "transponder type" key system which the T5 doesnt have???[/quote] Maybe in the 4 missing legs is the ignition?:mischievo

Post 251030 by AlanG on 2009-08-22 22:35:18

[quote=Johnny5;251023]Dont think so alan, cant throw away £100 ;)[/quote] Appreciate the outlay Johnny as times are hard. What about putting it back on fleabay? Hamish is reliable and honest and most importantly you have aftersales. Just a thought mate.

Post 251031 by Johnny5 on 2009-08-22 22:36:16

Hmmmmmmmmmm i dont know..... Instructions says for BMW E36 M3 and VOLVO 850 T5 the chip is shorter than the original by 4 pins (28 instead of 32)

Post 251033 by Johnny5 on 2009-08-22 22:38:22

Had thought of that Alan, but dont wanna sell a duff item on ebay if the chip is useless........ Im thinking ive done something wrong in the fitting of the chip to the board, wondered if there was anyone out there who could take a look at it for me, a second pair of eyes might reveal summat you never know??????????

Post 251034 by Tomcat on 2009-08-22 22:39:16

Tbh if it's a shorter chip then it's always possible that it's not in the correct position..i.e. if you've put the gap at the wrong end. Did you fit a chip socket or just solder the chip back in?. You'd be better buying yourself a chip socket from somewhere like CPC, solder that in and then you can try a few variations of fitting the chip without further damage to it.

Post 251035 by walter leever on 2009-08-22 22:41:20

[quote=Johnny5;251031]Hmmmmmmmmmm i dont know..... Instructions says for BMW E36 M3 and VOLVO 850 T5 the chip is shorter than the original by 4 pins (28 instead of 32)[/quote] Sorry to hear mate that it all went south:frown: But i was just thinking logical(i'm no expert) but when the original has 32 legs than in my opinion the replacement should have that to(with other info on it) Or am i'm being daft now?:slap:

Post 251038 by Johnny5 on 2009-08-22 22:43:01

I soldered the chip in like for like! (afterthought that a socket would have been a good idea) I used a low temp thin tip iron, lead free solder, a good flux and an anti-static wrist band Kinda took all the precautions i could bar putting a condom on aswell! lmao ;)

Post 251042 by Johnny5 on 2009-08-22 22:44:59

Walter, maybe you are right, im just going by the instructions that came in the box m8y! Think i need to have someone take a look at it for me before i do anything else, atleast i can use the car now i have a spare ecu!

Post 251043 by Tomcat on 2009-08-22 22:45:27

Lol, well other than having it a couple of pins out there's not much more you could have done. If I where you I'd get that socket ordered and fitted, then you can play around with the chip to your hearts content. Maybe also contact the original suppliers and ask their opinion. If you want me to have a look I will, I used to repair PCB's that owners had buggered up trying to fit upgrades etc.. You'd have to post it to me though.

Post 251047 by Johnny5 on 2009-08-22 22:47:58

Tomcat, Im going to PM you. Thanks J

Post 251305 by Johnny5 on 2009-08-23 21:35:06

Anyone know wether these ecu's self learn? The car is driving fine, although seems to be a little hesitiant and slightly underpowered :( Wondered if the ecu has to learn some parameters from my engine / driving style?

Post 251319 by walter leever on 2009-08-23 22:18:58

[quote=Johnny5;251305]Anyone know wether these ecu's self learn? The car is driving fine, although seems to be a little hesitiant and slightly underpowered :( Wondered if the ecu has to learn some parameters from my engine / driving style?[/quote] I think the ecu's are a bit self learning,but to what extend i don't know;

Post 251328 by AlanG on 2009-08-23 22:28:07

[quote=walter leever;251319]I think the ecu's are a bit self learning,but to what extend i don't know;[/quote] Mine learned origamy within 9 hours.....Sorry I didn't mean origamy..I meant correct afr and had the car running perfectly..

Post 251330 by Johnny5 on 2009-08-23 22:35:26

Hahahaha very good! So i guess i will have to drive it then! oh well....... hehe more fun for me ;)

Post 251333 by walter leever on 2009-08-23 22:41:27

[quote=AlanG;251328]Mine learned origamy within 9 hours.....Sorry I didn't mean origamy..I meant correct afr and had the car running perfectly..[/quote] Must have been a different one than mine,i've got it housebroke and fetching the newspaper:biggrin:

Post 251335 by p fandango on 2009-08-23 22:49:12

[quote=Johnny5;251305]Anyone know wether these ecu's self learn? The car is driving fine, although seems to be a little hesitiant and slightly underpowered :( Wondered if the ecu has to learn some parameters from my engine / driving style?[/quote] yes, mine takes about 4 cranks before it will even start & idle properly because of the mods i've done. I believe the Volvo books says it can take upto 75 mile to learn & set itself correctly

Post 251336 by AlanG on 2009-08-23 22:53:27

Johnny,ECUs do adapt and "learn" generally within a few miles. When I had mine re-mapped it took a number of miles for it to settle. Was misleading though as I was having idle speed issues beforehand but was perfect 850rpm when I changed the ECU. Within a couple of days the idle was at 1100 again so I called Hamish (HLM) and that was when I learned that they....well....learn. Vacuum leak. They have lives of their own mate..

Post 251995 by Johnny5 on 2009-08-26 18:25:00

@@@@@@@@@@@@ UPDATE @@@@@@@@@@@@@@@ Tomcat has my ecu now, lets hope the man can wave the magic wand! lol ;)

Post 252088 by sen on 2009-08-26 21:24:08

I am sure tomcat can sort it for you if anybody can he is master volvo :wink: