A bit bored so have been trawling youtube and found a few Autotech mapped 2.4 T5s and it's making me itch for more power.....
Just have to keep dreaming till can get back to work lol
A bit bored so have been trawling youtube and found a few Autotech mapped 2.4 T5s and it's making me itch for more power.....
Just have to keep dreaming till can get back to work lol
19t, greens, 3" inlet, 3" downpipe with race cat, V70R catback, autotech map...
310.2bhp / 333ft/lb
2016 Swedish Day UK "Best Modified Swede"
SOLD
Got an old discovery now.
Made me chuckle, brings back memories watching those two
I think you might need a bit more than a map for that!
Tony.
cut n blow dry,perms,and tinting prices on request!
Without a doubt. He has doubled the standard power i'd be over the moon if i made 330bhp ish
To be honest, it didn't look like a 500bhp car to me.
PIC][/SIGPIC]
aaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaa
Facebook^^^^^^^^^^^^^^^^ Old T-5 Kompressor Thread^^^^^^^^^^^^^^^ New TT-10 Kompressor Thread
stephenevans99 (Tuesday 9th April 2013),woody (Monday 8th April 2013)
Going straight for stage 2 mate, mte have quoted me 335
19t, greens, 3" inlet, 3" downpipe with race cat, V70R catback, autotech map...
310.2bhp / 333ft/lb
2016 Swedish Day UK "Best Modified Swede"
SOLD
Got an old discovery now.
Quoted from an email, my mistake it's 330 not 335bhp
"You get outputs of 330bhp with 480nm of torque with MTE's stage 1 on these later engines. Presently I am charging £395 including VAT for both Stage 1 and 2.
You need a full replacement exhaust such as the Ferrita stuff that I stock to run stage 2 which does not give you much in increased outputs but is usefull in maintaining outputs in warmer weather or when pushing on a bit when otherwise the ECU would pull back on targets if it senses or predicts rising temperatures."
That is from the Mte dealer, you know who I mean. I would have considered the autologic but since I have emailed Hlm and had no reply, and asked them on there thread about their new website if they now tune ex plod cars and had no answer then I don't think I will use them again. Have had a "custom" lol map and a 304 from them in the past and think it's time I see what the MTE Hype is all about or i might even change my mind again and go to shark, who knows lol
I thought those figures were with all supporting modifications etc etc not just the map!
Tony.
cut n blow dry,perms,and tinting prices on request!
so you and Martin will be knocking his door down then?
Tony.
cut n blow dry,perms,and tinting prices on request!
Owned since 2002. '96 Green 855-R, Manual M56H conversion by Russ @ RT Mech, 82mm rebore, THS Rods, Wiseco Piston kit, Decked Block, Machine work was completed by: www.mandjltd.co.uk, Refurbed head inc skim & 8 new valves, ME7 Ex Manifold, RICA304, Forge Blanking plate, 302mm set-up, PowerFlex Top & Bottom, Front Strut Brace, Miltek Cat-Back, R.I.P, IPD Cone Filter.
Latest update: 10000 miles as at 19/05/13.
To do: Lots (but don't tell Mrs Woody!)
Doesn't say they don't on their new site, so I asked and still had no answer. Had no problems with him in the past just think this time I'll pay the extra £100 and go MTE
dannyboy_turbo (Friday 12th April 2013),smithy (Monday 8th April 2013)
There are currently 2 users browsing this thread. (0 members and 2 guests)
Bookmarks