Hello. Anyone able to help of where to find performance parts fr volvo s40 t4 "99" model please. Looking for ideas and things for my car please. Many thanks. Mike.
Hello. Anyone able to help of where to find performance parts fr volvo s40 t4 "99" model please. Looking for ideas and things for my car please. Many thanks. Mike.
I'm not sure of specific locations, so it can depend on what you want.
An MBC can be sourced from anywhere
Air filters can be got from Demon Tweeks etc
More complex bits (or an example of what I've done)
An 850/S60R manifold with the fifth port cut off and welded up.
An 18/19t turbo
A set if VXR injectors
A custom exhaust.
Current Garage:
1997 960 3.0L 24v - Polestar...(Honest guv..!!)
1997 855 T5 S - stripped to 1300kgs gross weight - 14.2sec qtr(rank 17*)
2001 V40 T4 SE - 14.199@100.15MPH - Hybrid Turbo/VXR injectors and DeCat(Rank 15*)
*Data Sept 2013
Any Stuff For Sale - check out my Ebay link
I second that.
Been looking at these vxr injectors, what year are they and more info on the turbo would be great. What power would you get from this setup? And I've been trying to figure mapping out, as Ecu needs to be out, is it better getting it all then remap or just plug a piggy back ecu in?
Try to find a custom mapper before you change injectors and other hardware IMO. Phase 1 T4's are a lot more limited by their MAF, 312cc injectors and no one who maps them. To fit the bigger injectors you will need the MAF and injector parameters rescaling to suit. A piggyback may be an option but do your research before committing to buying all the hardware. I spent thousands on my phase 1 fitting a Holset turbo, forged engine, injectors, fuel system upgrades, intercooler etc etc, only to come to a dead end with mapping.
I think there was a guy on one of the forums (T5D5?) called Wingzero who successfully fitted a Unichip piggyback to his T4 but he had an MTE custom map as a base for when he tweaked his future hardware changes with the Unichip. MTE no longer do CUSTOM maps for the T4 which is a shame.
The phase 1 312cc grey injectors are near maxed at around 240bhp and the MAF airflow limit is 195g/s (250bhp ish).
I got 286bhp from my old phase 1 but had to fit VXR's to compensate for the MAF being maxed but this caused pig rich running in open loop before the MAF reached it's limit. The hardware was capable of a lot more but I wasn't prepared to fork out for a standalone to find out.
Phase 1 has the stronger block, but you will have a headache getting the software set up for any major hardware changes. The phase 2 block can be shimmed for far less than the cost of a piggyback or standalone ECU and setting up needed for the phase 1. Any 300bhp T4 is an extremely quick car and up to 300bhp it's arguable if you'd even need to shim the block. Some people have run far more and done trackdays without a problem. Some have reported cracked liners on stock cars!!
Everyone talks about wanting their T4 to be 350bhp+ but IMO a 300bhp T4 is more than enough. They really do go very well indeed and anything more than that on stock brakes and diff etc is going to be a waste.
The phase 2 has 420cc injectors (good for ~300bhp) and the MAF will reach also 300bhp before it reaches peak airflow. Also there is someone who can help with mapping on the phase 2 if you ask him extra nicely.
I plan on tuning my phase 2 eventually but I'm getting everything else (brakes, suspension etc) sorted first. I'm getting there slowly.
Mitch.
Last edited by mitchyboy01; Tuesday 27th May 2014 at 15:26.
Grey 855R Manual. Totally standard.
Great reply thanks. I don't want silly power I was looking at 300bhp absolute tops. Would the phase 2 injectors would ideal then? I will probably leave it at the exhaust intake and remap to be honest as it's just not "my car" it's for the little one too. Won't be putting any horse down unless this driveshaft makes way here hey! Ha ha
I know... the bloody driveshaft saga continues lol! Did u get my text mate?
Grey 855R Manual. Totally standard.
If i were to get a phase 1.5 t4 i.e the 1855 cc engine, but with the phase 2 updates (interior, exterior, etc), would it have the git ecu or the easier to map ecu?
"The problem with internet quotes, is that you don't know if they're real or not" - Abraham Lincoln
I'm not sure if the phase 2 injectors are straight swap physically. I used to know but its been a while since I had the phase 1. Either way, they are still 30% bigger than stock so will still run rich without the map being altered. VXR injectors are 50% bigger than stock so they will overfuel like a mofo. In closed loop (idle and part throttle) the ECU may just about be able to bring the AFR into spec enough for it to run OK.
Grey 855R Manual. Totally standard.
LiamT4 (Tuesday 27th May 2014)
Im not sure mate. The changover period from phase 1 phase 2 produced some quite oddball combinations I think. That's why I won't have another 1.5. Pretty sure if it had the 1855 it will be the phase 1 ECU but I can't be 100%.
Grey 855R Manual. Totally standard.
LiamT4 (Tuesday 27th May 2014)
The changeover period was around 2000 but because the way Volvo manufacture the 2000 motors may be registered as late as 2001 so the B194T2 1855 can be as late as that .......but whatever the date is if it has the 1855 engine then the ECU is the phase 1 EMS 2000 fuel system.
The B4204T2 in the year 2000 although a 2litre is still phase 1 ECU......but 2001 on the B4204T3 and the B4204T5 become phase 2 ECU because of the uprated MAF and injectors along with the extra engine sensors for Boost 1 and Boost 2 MAP
Last edited by 960kg; Wednesday 28th May 2014 at 10:47.
Mercedes C320CDI Sport Estate 3 litre V6 7 Gear Auto
Remap 290bhp 628Nm torque @ 1600revs 45.1mpg
LiamT4 (Thursday 29th May 2014)
i did pal been hibernating and baby shopping though. woooooooo ill get delivery arrange tomorrow bud ill ring first thing the morning!
do you think a loose driveshaft would of made it just slot into gear? im struggling to see how it would still at least grind would it trying because its not disengaged at the flywheel side.... confusing me now
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks