Join Today
Results 1 to 7 of 7
  1. #1
    Senior Member
    Forced aspirations
    TenaciousC's Avatar
    Join Date
    Jul 2008
    Location
    Warrington
    Posts
    313
    Thanks
    104
    Thanked 41 Times in 25 Posts

    Lightbulb WTF does the PCT Valve actaully do??

    Hi All,

    <<ERATUM : TITLE SHOULD READ PTC not PCT>>

    I've been making a study of the PCV system of my 850 for some months now (maybe even years) and have finally worked out where all the hoses are supposed to go.

    I am curious to learn of the functional purpose of the PCT valve (that sits on the main air intake pipe near the turbo). Everyone says we must clean it.... but no one explains what it actually does.

    The connections to it are as follows:

    1. Connects into main air intake.
    2. Large oily breather tube which goes around to the front of the block to the top of the oil catch tank
    3. Vacuum tube which goes to the left hand side if the intake manifold.
    4. Electrical connection

    I would assume that the valve opens to allow the blow by fumes back into the intake to be recombusted. But what is the purpose of the electrical control and vacuum tube ??

    Can any one explain its workings?

    Thanks in advance :

    C
    Last edited by TenaciousC; Tuesday 24th May 2011 at 10:58. Reason: PTC PCT

  2. #2
    Senior Member
    a 19t just isn't laggy enough
    p fandango's Avatar
    Join Date
    Aug 2004
    Posts
    19,785
    Thanks
    4,216
    Thanked 5,021 Times in 4,072 Posts
    i don't think theirs a valve there its just a small heater element

  3. The Following User Says Thank You to p fandango For This Useful Post:

    TenaciousC (Tuesday 24th May 2011)

  4. #3
    Senior Member
    Gizza job!
    Yosser's Avatar
    Join Date
    Jul 2008
    Location
    The 1980's
    Posts
    1,068
    Thanks
    161
    Thanked 417 Times in 315 Posts
    Quote Originally Posted by p fandango View Post
    i don't think theirs a valve there its just a small heater element
    ^^ this.

    Essentially it's just a T-piece that joins the crankcase ventilation system to the air intake. The other connection is to the inlet manifold, the idea being that at idle the vacuum will draw the crankcase vapour directly into the manifold.

    The electrical connection is just to a heater element that stops any water vapour freezing in extreme conditions.

    And it's PTC - Positive Temperature Coefficient.

  5. The Following User Says Thank You to Yosser For This Useful Post:

    TenaciousC (Tuesday 24th May 2011)

  6. #4
    Senior Member
    This user has no status
    Niles's Avatar
    Join Date
    Jan 2006
    Location
    On the Verge
    Posts
    2,434
    Thanks
    470
    Thanked 370 Times in 267 Posts
    Quote Originally Posted by p fandango View Post
    i don't think theirs a valve there its just a small heater element
    correct, its not a valve, its an air pre heater element for warming the intake air when its SUPER cold. developed for the Swedish market when the cars were designed.
    Not really required for the UK market. Its much the same as the little 'snow' guard that's clipped to the front panel covering the front air intake pipe. And......the reason Volvo stopped the 'reverse' intercooler kit was that in the Nordic winters the reverse kit was chilling the air so much that the throttle bodies could freeze up. Moving the turbo pipes to the way they are on the later ('94 ish on) was to warm the air a little in the very cold weather stop stop it freezing.
    The pre heater element CAN be removed from the air intake pipe BUT it must remain plugged into the loom as the ECU will notice somethings not responding & more than likely throw up a fault code.
    If you want to remove it you must pull the element, leave it plugged in and wrap/cover the element so it 'works' but will not touch anything that may damage it or be damaged by it.

    Make sense???
    .....sooper moose. '97 850R manual. Yum yum.

  7. The Following 2 Users Say Thank You to Niles For This Useful Post:

    p fandango (Tuesday 24th May 2011),TenaciousC (Tuesday 24th May 2011)

  8. #5
    Senior Member
    Gizza job!
    Yosser's Avatar
    Join Date
    Jul 2008
    Location
    The 1980's
    Posts
    1,068
    Thanks
    161
    Thanked 417 Times in 315 Posts
    Quote Originally Posted by Niles View Post
    The pre heater element CAN be removed from the air intake pipe BUT it must remain plugged into the loom as the ECU will notice somethings not responding & more than likely throw up a fault code.
    If you want to remove it you must pull the element, leave it plugged in and wrap/cover the element so it 'works' but will not touch anything that may damage it or be damaged by it.
    Not sure if that's correct.

    I have mine disconnected on the S70R and there are no fault codes.

  9. #6
    Senior Member
    Forced aspirations
    TenaciousC's Avatar
    Join Date
    Jul 2008
    Location
    Warrington
    Posts
    313
    Thanks
    104
    Thanked 41 Times in 25 Posts
    Thank you Gentlemen for these excellent answers. It all makes sense now.

    :-)

    C

  10. #7
    Senior Member
    a 19t just isn't laggy enough
    p fandango's Avatar
    Join Date
    Aug 2004
    Posts
    19,785
    Thanks
    4,216
    Thanked 5,021 Times in 4,072 Posts
    binned mine with no ecu faults (well no faults about that anyway lol)

    just a curious question here. On BT the small vac pipe from the PCT to the inlet went via a metal tube which went around the top of the head (under the sparkplug cover), again this was done to get the heat from the engine. Was this another bit just on early 94's or did they carry in on for a bit longer
    Last edited by p fandango; Tuesday 24th May 2011 at 17:13.


 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
ipv6 ready