Have you tried the recirculating inlet check valve shop?
..No seriously, how about a brake servo line check valve off a scrap car from the breakers.
Type: Posts; User: thedrill; Keyword(s):
Have you tried the recirculating inlet check valve shop?
..No seriously, how about a brake servo line check valve off a scrap car from the breakers.
Ive seen a snapped one on a 855 td on a 1996 N plate at my work, (garage where I M.O.T).
would my 16" centaurus alloys off v70 ,also fit 302mm discs?...they are 7" wide instead of the standard 6.5" T5 alloys.
Ive got the kalmar union kit on my t5, works fine and not too noisy and doesnt cause any problems with stalling .
Just get a custom exhaust job done to fit the existing manifold, to exit from the rear..
I dont think its a requirement to have self levelling on new cars either, as some new (3 year old) cars do not have them fitted. Its certainly not an M.O.T requirement either, as long as the lights...
Sounds like the solenoid is staying engaged for too long, possibly needs strip down and overhaul.
Plenty of those in Wales m8..... :troutslap
That was the answer I was looking for , sorted! ..I will get it vacuum checked before going ahead with a re-gas.
Thanks.
Hi all, Ive had my 1995 854 for a couple of months now and knew when I bought it that it didnt blow cold at all, so I thought I would have a look at it today. All the relays and fuses are intact and...
look here..if your quick.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=4571037849&ssPageName=ADME:B:WN:UK:17
Its under the drivers side, remove the panel below the steering wheel (3 screws) and look up to the right hand side and you will see a load of relays, if you see one marked up with the numbers 210...
Alarm relay was missing! Got one off e-bay for a tenner posted..plugged it in and the doors locked, set the ignition on and off five times and pressed the button on the remote keyfob and voila..its...
No, they are from Alldata (usa I think).
From Autodata 2004...0.7mm for ngk plugs..
0.7-0.8 for volvo plugs
0.8 for autolite
0.7 for beru
0.7 for bosch
0.7 for champion :pants:
Well thats what the book says.
I think its 0.7mm which equates to : The back of a fag packet!! lol.
Already got these, and Audi data for the same programme, quite good too.
The ABS light should light when the ignition is on and should go out when the car is started, there is a list on the wall of M.O.T stations to tell you of the correct procedure for this.. as some...
Isnt that Quarter of an inch :troutslap
Just changed my Cambelt on my T5, not a bad job really and didnt have to remove all of the plastic covers.
Its only done 40000 miles since volvo changed the belt (volvo sticker) but was five years...
Hi Jim, does your central locking work fine with the key and deadlock too? but the LED on the dash wont flash at all...Ive had a look for the alarm relay and cant find one..the only thing that I can...
This is where I moved mine to...
http://www.volvot5.co.uk/forums/showthread.php?t=3541
Hi , I had a similar problem with a tyre that had worn unevenly , causing a noise like you described..check the tyres for uneven wear or feathering of the treads, mine sounded like a wheel bearing...
Does anyone know where the Alarm immobilizer relay should be situated?
I think mine has been bypassed, I have been on to volvo today and they say that my car has an remote alarm fitted, and the...
Ive been looking under the dash for the alarm relay box..cant find it..What I have found is a blank relay socket with two wires and a fuse joining them together..remove the fuse and the car will not...