Search:

Amp is located behind the cubby hole on the LHS of the boot. Pop the cubby out and shine a torch in or if you're feeling like a more in-depth examination, pull the side panel trim off and have a...

I used to sell those back in the day, they were £250 new! Pretty good deal!

(I've got the next one up in the range, the SHX-701T with colour LED screen and DAB box - not parting with it for the...

Just a quick update to this - it seems to have rectified itself and all is working fine.

For reference, you need to remove the back seats and parcel shelf to get to the module and associated...

I went through the fuse board listing on the fuse cover but there was nothing specific to 3rd brake light. I guess I could test all the fuses if it came to it.

The fact the bulb fail warning light...

Also, could it be something as daft as a fuse, or is that wishful thinking?

Hey all, just a quick question - I've noticed the 3rd brake light on my C70 has expired with the associate brake warning light on the dash. The others are working, but I need to get it sorted asap.
...

no unfortunately not - I've had other ones apart and usually it's a load of springs that are pretty much almost impossible to refit.

sounds like the laser might just be dirty though, I'd try...

What's it doing (or not doing) - does it read the TOC of the CDs or does it just eject through the cartridge before ejecting it?

Might need more than a cotton bud clean if the laser is out of...

It's all good fella :) I just licked a cotton bud when I did mine - I'll probably give it a good going over again when I can be bothered - it got to a stage on mine where it wouldn't read any CDs at...

There's also a dolby controller box sitting on the centre tunnel behind the dash. Iirc if the heater matrix goes, it can douse this box in coolant which doesn't really make it work tip top, so could...

The 901 is dead easy to clean out without removing the inner cover over the CD mech. Undo the single screw on the back, pop the top off, sellotape two cotton buds together, put a blank cartridge in...

just revitalising this, it's dead easy to get the 901 working again, I did it myself yesterday...

Make sure you've got your radio code before you start.

Basically, take the unit out the dash...

I think this one is excessive to the point of ridiculous! I would probably be able to knock it out the mount using just the force of gravity!

the oem mount is meant to be loose in the housing?!?!

what's the point in having the mount there - the engine rocks and rolls all over the place!

I bought the upgraded OEM part (square block type) and the bloody thing has failed on me.

What I thought was a split gearbox torque mount, is actually a worn out torque mount with a failed top...

That volvo handsfree kit is a Motorola one, probably debadged... just thought I'd chip in :P

11m turning circle??? that must be on a good day...

I think the Exxon Valdez could out turn mine!

water under the car could also be expelled from the aircon system, it's not a guaranteed hose problem - esp if it's only doing it occasionally...

aircon drainage is perfectly normal too...

on mine it was the ring around the barrel too, it's occasionally doing it again now though which is a bit of an irritation, I find if I hold the key flat to the lock before putting it in, it works...

the manual ones in mine work to tilt the seat, but only sporadically work to slide it forward - I usually have to manually slide the seat forward with the front adjuster before having the prospective...

Bank top did the job for me yeah, I'm not in sunderland myself but you could give em a buzz on 0191 549 7500 to see how much they'd charge :)

ah right, no worries... might have a punt towards the end of the listing :)

you got a ballpark figure you're hoping to get for it?

whistling like that is usually a poor earth, might be worth giving the head unit it's own earth rather than trusting the one that comes through the loom...

doesn't an IMIV work with the HU-803 for...

squeaky brakes could be a cheap compound, I had the same problem...

bought cheap ATE pads from ECP which must be about 85% metal! Put some EBC reds on the car, and relocated the squeal to the back...