Join Today

Search:

Type: Posts; User: dant5r; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    50
    Views
    13,407

    It's horse not bull............ once the horse...

    It's horse not bull............ once the horse has bolted.
  2. Replies
    31
    Views
    10,981

    The sensor needs to be fitted to the downpipe...

    The sensor needs to be fitted to the downpipe with the aid of a weld on boss.

    The correct reading at idle and normal driving is 14.7 - 15.0
  3. Replies
    31
    Views
    10,981

    The ecu will being it's hardest to make the...

    The ecu will being it's hardest to make the engine run at the correct air fuel ratio.

    The knock sensors detect knock and the ecu then either adds fuel or retards the ignition to overcome the...
  4. Replies
    31
    Views
    10,981

    Two things jumped out at me reading your post, ...

    Two things jumped out at me reading your post,

    83mm pistons and stock tune.

    The 8mm pistons will make it a 2.4 so is the stock tune for a 2.3 or a 2.4 ?

    If it's a 2.3 then you are running...
  5. Replies
    14
    Views
    4,612

    If you noticed when you removed the old seal they...

    If you noticed when you removed the old seal they was a small groove in the crank where the old seal had been. If you fit the new seal if in the same place the chances of it leaking are greater. If...
  6. Replies
    6
    Views
    1,719

    The correct way to solve this fault is to clean...

    The correct way to solve this fault is to clean the idle control valve with carbon cleaner or replace it.

    Unplugging it will just make the engine run rough and put the engine management light on.
  7. Replies
    12
    Views
    2,688

    It's obd2

    It's obd2
  8. Replies
    12
    Views
    2,688

    The car is a late 95 850 t5r. I have VOL-FCR...

    The car is a late 95 850 t5r.

    I have VOL-FCR which I used to read the codes.
  9. Replies
    12
    Views
    2,688

    Fault code EFI - 355

    I keep get a fault code of EFI 355 which is mass air flow signal fault.

    I've replaced the sensor with a known working one but after about 5-10 of driving the lambda comes on. When the lambda light...
  10. Replies
    32
    Views
    4,594

    I was looking at the top red which must be torque.

    I was looking at the top red which must be torque.
  11. Replies
    32
    Views
    4,594

    I'm I right in think that it made 317bhp at 3500...

    I'm I right in think that it made 317bhp at 3500 rpm ?
  12. It could also be the seals in the clutch master...

    It could also be the seals in the clutch master letting by.

    Check if the carpet is wet around the top of the clutch pedal where the mastet connects to the pedal.
  13. Thread: Lack of Boost

    by dant5r
    Replies
    5
    Views
    1,318

    Unfortunately this will not work as the engine...

    Unfortunately this will not work as the engine will not produce boost when on a fast idle.

    You are better off spraying easy start over the boost hoses and seeing if the idle increases.
  14. Thread: turbo housing

    by dant5r
    Replies
    2
    Views
    1,016

    turbo housing

    http://pages.ebay.com/link/?nav=item.view&id=191593725392&alt=web

    Has anyone had any experience with this manufacturer ?
  15. Try getting in contact with Avinitlarge on here....

    Try getting in contact with Avinitlarge on here.

    If you read oblarks remapping thread he sent his ecu to him to have the ostrich fitted.
  16. Replies
    21
    Views
    3,145

    If you switched the engine off when the oil...

    If you switched the engine off when the oil warning light came on you could have damaged the crank bearings.

    The oil pressure switch only needs 10psi to turn the warning light off and the...
  17. Weld the rivet nuts back to the chassis.

    Weld the rivet nuts back to the chassis.
  18. Thread: shake & shine

    by dant5r
    Replies
    4
    Views
    2,590

    Thats the stuff :) Has anyone used it ?

    Thats the stuff :)

    Has anyone used it ?
  19. Thread: shake & shine

    by dant5r
    Replies
    4
    Views
    2,590

    shake & shine

    Has anyone used that carplan shake and shine ?
  20. Replies
    185
    Views
    48,812

    with the mods he's doing (19t, me7 blues, 80mm...

    with the mods he's doing (19t, me7 blues, 80mm maf & a 2.5" exhaust) he should be knocking on the door of 300 brake.
  21. Replies
    467
    Views
    107,672

    It's a shame he didn't do the work himself as...

    It's a shame he didn't do the work himself as most people on here are home mechanics.

    But this thread show what you could do with a blank cheque
  22. Replies
    348
    Views
    208,451

    Isn't that a m4.4 ecu?

    Isn't that a m4.4 ecu?
  23. Replies
    5
    Views
    1,872

    Shame no one else does........

    Shame no one else does........
  24. Replies
    65
    Views
    18,137

    One thinks that James has spat out his dummy.

    One thinks that James has spat out his dummy.
  25. Replies
    65
    Views
    18,137

    Don't you mean "useless information"

    Don't you mean "useless information"
Results 1 to 25 of 128
Page 1 of 6 1 2 3 4
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
ipv6 ready