To get to that bhp you will need.
Bigger MAF (ideally 3.5")
Bigger injectors ( 550cc or VXR injectors)
And a larger turbo ( kkk24)
Then a good map for the above upgrades.
And lastly a...
Type: Posts; User: oblark; Keyword(s):
To get to that bhp you will need.
Bigger MAF (ideally 3.5")
Bigger injectors ( 550cc or VXR injectors)
And a larger turbo ( kkk24)
Then a good map for the above upgrades.
And lastly a...
Had a productive day, removed two rusty wings and fitted the P80 early 70 series front end.
33099
33100
33101
33102
A picture speaks a hundred words.
33087
33088
33089
33090
I don't know why people get so worried about the cam thrust faces being broken, as long as they is a good portion of the thrust face left on the head and on the cam cover the thrust face will do it's...
I'd throw the Turbo tuner ecu in the bin and go for M4.4 with an ostrich, alot easier to tune :)
Parts for the next upgrade coming together.
33075
From my understanding is the 6+6 billet wheel makes its boost lower down the rev range compared to the 11 blade billet wheel makes it boost higher up the rev range.
I'm running a 6+6 billet wheel...
After having a flat battery I've noticed a slight hesitation when driving at around 30 mph the hesitation goes if you drive it like you stole it. I recorded a run to the supermarket this Saturday and...
Haven't done much to old girl since the last update. I've always put Esso super plus 97 and she's ran OK on it but now Esso have gone to super plus 99 she runs like a trooper the little bit of knock...
The kit is listed to fit V70/S70 AWD from 98 - 00
I've put some miles on the bc coilovers and I can report back that the ride is a great improvement over old suspension.
The front have just...
Update time.
Had a MOT last week and passed with 2 minor defects, 2 driveshaft CV boots split which is a PITA as they are only 2 years old and covered 1500 miles.
As just about everything has...
I've been running the VXR bin file for a couple of weeks and all is running fine apart from the fact I'd forgot to change the MAF fault threshold values, This was a bit of blessing as the MIL light...
I wouldn't mind try this bin file when you have finished testing it just see how it compares to mine 608 bin file.
Had a week off so I thought it was about time I fixed some of the long term problems eg no air being blown on the windscreen. So out came the dash followed by the heater unit, the fault was found to...
I've had to put the maf problem on the back burner as I've had a more pressing problem.
The old car started to splutter when the manifold pressure went from vacuum to pressure. At first I thought...
I get about 25mpg on short runs with the D5 gearbox, AWD and using the 2.3ltr 608 bin set up for 2.5ltr.
For the last few months I keep getting the same fault code of EFI-355 (mass air flow senso fault) I've fitted secondhand,aftermarket and even OEM sensors but after a day or two the MIL light comes...
Up date time.
I thought it was about time I upgraded the fuel pump as the VXR injectors at 3.8 bar was starting to push the oem fuel pump to it's limit. So I went for a ASNU 340lph fuel pump, the...
It's been a while since I've updated this thread, I've taken up running and have been busy training, over the last year I've completed 2 half marathons and 6 10k's. But due to the Covid-19 out break...
I've been doing some data logging at WOT with 18.5 psi of boost and it looks like I'm maxing my VXR's out already.
32412
Also I'm at my max load as well. I don't want to go back to the extended...
I've been chasing what I thought was a misfire when coming on boost, I've tried 2 sets of OEM plugs which I've gapped them from 20-30 thou and a new set of OEM coil packs which didn't cure the...
Ever since I fitted the Bosch 550cc injectors I've had a problem. Straight out of the box they ran lean at idle regardless of my increasing the injector dead times, so I pulled the ECU over night to...
I was running my greens with a TEMIN value of 0.24 for years with no problems.
Up date time
A few weeks ago the old girl developed a miss fire when under load so some OEM spark plugs were purchased from FRF. The old plugs looked OK, a nice dirty white electrodes, but once...
I have a couple of pulleys and a couple of solenoid blanking plates left over.
Yeah just fitted the a solenoid blanking plate will stop the oil feed to the VVT pulleys. If I can help just shout...