Leaving this converstion.
Type: Posts; User: bongodave; Keyword(s):
Leaving this converstion.
Not bled properly then eventually corrected itself.
didn't clock diesel.
Before you do anything, change fuel filter, air filter and oli/filter, then see where you are.
Restricted fuel due to cacky/gelled filter due to water ingress or bio-diesel...
I would def service engine and change air filter for a K&N panel first. Check another recent thread on here regards filter.
Also take a preliminary look at any pipes you can see around from fron...
I wanna Burberry tail-pipe with baseball-cap mufflers that roars, 'Innit' when you go over 5,000rpm.
Your not gonna go wrong with semi-synthetic for over 80,000 oir fully stnthetic for under. I am pretty confident you will find concensus there.
Fault sounds like mine, MAF sensor. Any lights...
I'm not buying anything till it's gone on a scanner. lol
Think I'll be doing this....
http://www.ebay.co.uk/itm/BOSCH-VOLVO-C70-V70-S60-20V-5-CYLINDER-MASS-AIR-FLOW-METER-/321276890128?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item4acd984c10
Am hoping it one of smaller sensors as car is running fine. Understand it splutters and misfires when Maf goes.
They're £90 for Bosch on Ebay now for my year anyway. All of a sudden that doesn't feel so bad now.
Will see what reader brings up first as car feels smooth and no mis-fire, just light on and...
oof, I'll be going breakers then as Volvo ones are 4 times the price.
Fair do's.
Just that I saw article on.I think, Wheeler Dealers and looked prety impressive. The 60 grand for a kitted van thing stuck in head.
Not touched anything, bar carefully removing, and re-fitting ecu. Disconnected batt which fixed it for 40-50 miles but came back on.
Got dongle for obd2 on order so will see what's wrong.
Ta...
And bigger marks either grind out, or fill with metal epoxy and grind.
It really is do-able to a very good standard if time is taken. If you use Plasti-dip or similar it is even easier. Although...
Sorry,that'sjust not the case. The guys now travel around with over 60 grands worth of gear and the finish is equal, if not better than dropping off. The wagons have tyre machines, compressors,...
If you getting the tyres off you can do an even better job! lol. Independents will charge you a fiver to knock off a tyre!
Dare ya. It's fun and gets ya connected to your motor and saves you a...
If they are deep, angle gring them back then use emery cloth. Otherwise, just emery cloth.
Ifyouaint got an angle grinder, silverline do a half-decent one for under 30 quid at toolstation.Worth...
Couple cans aerosol and a deck of playing cards to stick between rim and tyre to mask.
Actually easier than you think.
This aint yer average flexi tbf. It's designed for exhausts and to be welded, so not your spin-dryer stuff.
Catch ya later mate.
Better still as plasma, more detail and full kit inc pillar-mount!
http://www.ebay.co.uk/itm/181218903262
Looks a simple addition to your bleed valve mod.....
...
Seen these kits are silly expensive. How about this for an alternative. stainless 3" rip kit.
Bloke says more you buy, cheaper etc and bonus here is smooth inside. There's a guy selling...
Gotta be red or blue. VHT aerosol is a fiver on ebay.
I had a gearbox (manual) that was very crunchy. Convinced synchro hubs had gone,i was gonna scrap. Someone told me to drain and replace with fully synthetic ep 80/90/
Sceptically did this and...
Hahahahaha. Ok....ssshhhhhhh!!!!