Join Today

Search:

Type: Posts; User: MoleT-5R; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    4
    Views
    89

    Even though you are quite correct here, the OP...

    Even though you are quite correct here, the OP was talking about the me7 Intake manifold, A mistake I nearly made too...
  2. Replies
    4
    Views
    89

    I only know of one person who has done this, It...

    I only know of one person who has done this, It seemed a lot of work for what seemed to be very little gain, and he has swapped back now to the older manifold, search Oblark's 850 project threads. As...
  3. Replies
    12
    Views
    261

    Another question is dose it not unlock at all or...

    Another question is dose it not unlock at all or just not unlock on the passenger side, which is my problem, it isnt really really stretched cables (I have to agree with Lee here) , in my case what...
  4. Replies
    12
    Views
    261

    That will more than likely cure the issue Mark,...

    That will more than likely cure the issue Mark, will have stretched by now for sure. Gul's bonnet link cable has stretched that much I have to lift the bonnet to slip my hand in on the drivers side...
  5. Nice work Woz, I'm expecting my brackets to be in...

    Nice work Woz, I'm expecting my brackets to be in about the same condition, when I final get around to doing the job.
  6. Thread: 850 glove box

    by MoleT-5R
    Replies
    2
    Views
    140

    What has happened to it ?.. Is the catch not...

    What has happened to it ?.. Is the catch not working by any chance. What colour do you need ??
  7. Just be a little careful with xc90 disc's and...

    Just be a little careful with xc90 disc's and calipers, as by local motor factors informed me there 3 different sizes of front disc's listed, when I went for pads recently.
  8. Replies
    10
    Views
    291

    I had the same on our v70r awd, but the hose came...

    I had the same on our v70r awd, but the hose came clean off and she didn't run at all well until it was fixed, took a little head scratching and finding, but a simple fix in the end.
  9. Replies
    10
    Views
    291

    I'm not an expert on these, but ME7 engine...

    I'm not an expert on these, but ME7 engine management and dump valves don't go well together from what I remember, a plumbed back/recirc type are required to keep things sweet from what I recall as...
  10. Replies
    27
    Views
    1,010

    Glad you've got it sorted, now you can really...

    Glad you've got it sorted, now you can really enjoy your Volvo.
  11. Replies
    4
    Views
    315

    lol...I think most are at the suspension fully...

    lol...I think most are at the suspension fully needs to be re-built stage tbh... my cars included, some of mine have had new shocks all round etc... but you still find them wanting something...
  12. It sounds like the immobilizer code is missing,...

    It sounds like the immobilizer code is missing, so I doubt swapping the chips out will make any difference. Whilst typing I remembered a useful post from 960kg (Keith) a few months back, this would...
  13. Replies
    2,191
    Views
    176,705

    It's good to here that work is still progressing...

    It's good to here that work is still progressing Dave, but as you say, it is hard to keep pushing on with these projects and even harder when our main 1/4 mile playgrounds have been closed. Hopefully...
  14. Replies
    12
    Views
    314

    Nice find Keith, I'd be very suspicious of the...

    Nice find Keith, I'd be very suspicious of the vac pipe to the fuel pressure regulator and the little rubber elbow into the inlet manifold on left hand end, hidden behind the power steering pump,...
  15. Replies
    12
    Views
    314

    I get the code on my 855 T-5r (motronic 4.3), but...

    I get the code on my 855 T-5r (motronic 4.3), but does not seem to effect the performance much if any, but does chuck up the MIL/Lambda light. I just normally cleared the code if the code came up...
  16. Replies
    82
    Views
    21,227

    won't the 850's maf surface area be under size...

    won't the 850's maf surface area be under size for the housing then, or do you then adjust the scaling to allow for the smaller surface area of the 850's sensor to the diameter of the maf housing,...
  17. Replies
    12
    Views
    314

    Then again thinking on about this issue, from my...

    Then again thinking on about this issue, from my experience on my remapped car it, isn't unusual to see this code as it does relate to long term fuel trim, I get this when cruising on the motorway on...
  18. Replies
    82
    Views
    21,227

    Something I should be considering really, as the...

    Something I should be considering really, as the standard one must be maxed out pulling 301.2hp on the dyno with the lowly 15g, I do have a 3" here to play with, but it may be easier just to go up to...
  19. Replies
    12
    Views
    314

    should be on the fuel rail for that year afaik,...

    should be on the fuel rail for that year afaik, the same as the 850's
  20. Replies
    82
    Views
    21,227

    How bigger MAF did you get..?

    How bigger MAF did you get..?
  21. Replies
    82
    Views
    21,227

    Just had a full set of drilled and grooved discs...

    Just had a full set of drilled and grooved discs for gul, 302's for the front instead of the standard 280s she currently has. Olive will be next and will move up fron her current 302's, but to what...
  22. Replies
    82
    Views
    21,227

    Lol just as I posted that the image...

    Lol just as I posted that the image appears....pmsl
  23. Replies
    82
    Views
    21,227

    I see no image......guessing brakes. .?

    I see no image......guessing brakes. .?
  24. Replies
    82
    Views
    21,227

    Nice work Dave and very smart graphics, are you...

    Nice work Dave and very smart graphics, are you about at all soon for a demo???
  25. Replies
    27
    Views
    1,010

    Just a thought if you still run the original...

    Just a thought if you still run the original by-pass valve on the turbo, check if the diaphragm is not split or broken, that could possibly give the whoosh you mention and would also cause a loss of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
ipv6 ready