Join Today

Search:

Type: Posts; User: Tim Williams; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1,018
    Views
    168,749

    13.2 @ 117MPH at Shakespeare today, thank you for...

    13.2 @ 117MPH at Shakespeare today, thank you for having me again.
  2. Replies
    174
    Views
    29,356

    I finally got to have a go, my other attempt to...

    I finally got to have a go, my other attempt to get there last month ended in a failed diff and gearbox before I even go to Shakespeare. It was nice to meet up again inc the homeless man...
  3. Replies
    11
    Views
    3,134

    If you start with the cam timing and then a...

    If you start with the cam timing and then a compression test. Don't forget to check the cam timing you will need a cam locking tool and a new blanking plate for other end of the inlet cam. You can...
  4. Replies
    126
    Views
    48,811

    I fitted quite a bit of wiring to the N/S/R 1/4...

    I fitted quite a bit of wiring to the N/S/R 1/4 sometime ago.
  5. Replies
    21
    Views
    7,706

    I forced my P2 flip key open and changed the pin...

    I forced my P2 flip key open and changed the pin and spring, it was a bit hard to break open but once back together you would never know.
  6. Replies
    20
    Views
    28,586

    Bell End.

    Bell End.
  7. Replies
    8
    Views
    3,247

    £50-100 as a Trade in or as a big project...

    £50-100 as a Trade in or as a big project posssibly as much as £700.
  8. Replies
    2
    Views
    1,108

    Your map won't alter no matter who loaded it.

    Your map won't alter no matter who loaded it.
  9. Replies
    175
    Views
    312,560

    Are you after a standard or Quaife diff?

    Are you after a standard or Quaife diff?
  10. Replies
    6
    Views
    2,028

    You really need a code reader. By swapping plugs,...

    You really need a code reader. By swapping plugs, coils and injectors around you should be able to pinpoint which parts are at fault.
  11. Replies
    19
    Views
    6,230

    You won't split a liner with an 81mm block with...

    You won't split a liner with an 81mm block with standard rods, as already said it's most likely the head gasket. Get the head skimmed and also change the coolant cap.
  12. Replies
    594
    Views
    183,913

    I don't like fibre gash splitters. That looks...

    I don't like fibre gash splitters. That looks quite good.
  13. Replies
    20
    Views
    25,042

    It looks more yellow now :doh:

    It looks more yellow now :doh:
  14. Replies
    20
    Views
    25,042

    It looks like they didn't listen to you, it still...

    It looks like they didn't listen to you, it still looks yellow��
  15. BBS split rims use M7 x 1.0.

    BBS split rims use M7 x 1.0.
  16. Replies
    10
    Views
    4,278

    In the U.K. The only turbo ones we got were 2.0T...

    In the U.K. The only turbo ones we got were 2.0T LPT and T4. The 2.0 T is 83mm bore and the early T4 was 81mm, the later T4 83mm bore. I think in the USA your T4 with an 83mm bore was the same as our...
  17. Replies
    8
    Views
    2,086

    That's the pipe I thought it was, if it is then...

    That's the pipe I thought it was, if it is then I've only known one to leak. They are a pain to fit as the turbo and exhaust manifold needs removing.
  18. Replies
    8
    Views
    2,086

    If it's the main water pipe from the bottom rad...

    If it's the main water pipe from the bottom rad hose to the back of the water pump then most Volvo breakers will have them on engine's. I should have some but I wouldn't post it.
  19. Replies
    175
    Views
    312,560

    They work well, Adam from Wales did it on his...

    They work well, Adam from Wales did it on his 854R. Iirc volvo have now ran out of some of the rear suspension mounting brackets, they are easy to remove from a donor. I think Shem got a couple of...
  20. Replies
    594
    Views
    183,913

    The IPD one is the best fit, better than factory....

    The IPD one is the best fit, better than factory. The DO88 is fine you just need to take care with the hose clip on the ETM. Don't use the crap Chav clips, use good wormdrive clips.
  21. Replies
    16
    Views
    4,966

    The plastic oil pressure relief valves can stick...

    The plastic oil pressure relief valves can stick open, when they do you will still have some oil pressure but not sufficient to safely run the engine. The oil pressure switch thread size is very...
  22. Replies
    16
    Views
    4,966

    If it's the oil pressure switch it won't make it...

    If it's the oil pressure switch it won't make it unsafe to drive. If the oil pressure switch is fine and you drive it you should hear a slight tapping after a couple of miles followed by a loud...
  23. Replies
    8
    Views
    4,408

    They don't look to be running lean but if you...

    They don't look to be running lean but if you haven't driven it hard it won't be possible to see if it's lean when pushed.
  24. Replies
    8
    Views
    4,408

    They are due a change, importantly they don't...

    They are due a change, importantly they don't show signs of burning oil but they do show you drive like a pussy lol.
  25. Replies
    467
    Views
    106,786

    I'd rather if possible not do the drivers door...

    I'd rather if possible not do the drivers door handle a third time...
Results 1 to 25 of 456
Page 1 of 19 1 2 3 4
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
ipv6 ready