Not a hope in hell's chance!
When I fitted my FMIC, I had literally mm's spare top, bottom, front and back.
You will need to retro fit it elsewhere on the front, maybe behind fog lights or...
Not a hope in hell's chance!
When I fitted my FMIC, I had literally mm's spare top, bottom, front and back.
You will need to retro fit it elsewhere on the front, maybe behind fog lights or...
Rear calipers from an XC90 will bolt straight onto the rear of the S60/V70 but they are only slightly bigger than the standard ones already fitted, that said...you would then have vented discs rather...
Have a watch of ipd fitting a guage.
https://youtu.be/_XQHbdgit0o
He used a long steel rod with a bend in the end which threads inside the panel through the hole where the wires go into the door and pressed the big dent out from inside, he used a reflective thing...
Hello Joe,
MTE stage 1 calibrations on your 2.4T will give you outputs of 235bhp with 380nm of torque.
Cost and installation as above.
\Don.
Would this be a good time to raise the question as to whether V70R bumper should be used. I think it doesnt look that good on the coupe.
23040
the mgf was fabric to. iit done a fantastic job. ill see if ive got any old pics of befor and after
PP is good for me - 60 delivered
A good video here, although it is pitched at selling the Xemodex item...
http://xemodex.com/technologyimproved/video-8644347
Never used used them but hth....
http://www.driven2automotive.com/air-flow-meters-/81-air-flow-meter-0280218108.html
DRIVEN 2 AUTOMOTIVE
Unit 10
Parrett Works
Martock
Somerset
TA12 6AE
I never heard of nor been convinced by any repaired gearbox AW-52 or otherwise. As far as I am concerned - the only good way to repair a dodgy autobox is first to flush/change the ATF. If that...
Hi, try the software below:
http://www.directdownload.bz/Scan-xl-new.exe
Please follow the instructions for installation. when you get to the registration section enter your name and...
just thought id mention this as im doing an x reg c70 ragtop at work at the moment,a steering rack change,
reason for change is the welds have broken,
the welds that fits the mounting points to the...
OK - the stuff is on - ebay seller was great. Bought two lots of the product for £15 but frankly looks like I only need 1 as I've given all the door seal, boot seal and the roof seal a coat and in...
Thanks silverback02
There are a few c70 vids about but I thought this one was really worth seeing for the people who read this forum.
bolt ups will be the same but the ball part would be different I think, different length shaft or something i seem to remember.
I think mightywolf is correct unless you know a very good locksmith that would cut it for you and then you need someone that could clone your transponder and place it in the key. Some years ago I was...
I think you still have to take them to volvo to have them cut and they defo need programming to your car by volvo. Someone will correct me if i'm wrong about the cutting.
Thanks for the useful info. I removed it from the other section you posted it in, as we don't allow duplicate threads.
Cheers...
Hi Joe, i've replied to your post on VOC so won't bother typing it all out again lol
Simon,
Thanks for all your help with mine.
Ian:smile:
Nice one...but my Dad's a fireman and a Policeman..nah nah nah nah naahhh :cop:
you can stick a 16t on it and then put t5 injectors in all a straight swop and get the car mapped up should be good for around 280 bhp fly
Im sure compression ratios are different..? So high boost isnt all that clever.
I don't think just going to a HP Turbo is practical as the main engine ECU fuel pump and regulator plus injectors may all need to be changed. I stand to be corrected though? after all if you through...