Search:

If the ABS light is on before the brake test is performed then it's a fail.

If the light comes back on when you are in slow traffic i would try a known good MAF...
The code you have offered is certainly air leak realted tho if the pipework is known to be sound a new maf is...

Be fine mate,the worst one to access is the one at the timing end of the fanimold. All others are a 5 min job providing you have the replacement pipe......

Hi Rob S. They're Int'ebay, but I should add there's another 20 quid postage. If you bid $115 you'll get em, but it might take em 4 days to accept. Through paypal ex-rate is 1.6 which is...

Its a relatively simple job, locate the plastic 'button' clips around the edges of the door card and press the centre of them in positively. Next use a thin & wide flat blade screwdriver or similar...

Yes the CV joint obscures the wheel bearing bolts, so the driveshaft has to come out first.

And yes I did remove the caliper completely but only undid the caliper bracket bolts as there is no need...

when i had the 280mm brakes i put some drilled and grooved discs on from ebay a pfirm called motorsport fabrications and i cannot falt them and couldnt over heat them and i always use genuine volvo...

Most people say that Genuine OEM ones are as good, if not better, than any of the grooved/drilled aftermarket ones of same size/caliper.

The 302's would fit under Perfo's, just the same as std V70...

if ur keeping ur 16s then u cn fit any aftermarket brakes of the standard size,
drilled,grooved etc etc.
it all depends how much you want to spend.....
each brake varies in working when cold or...

Hey Rob

The 302's wil not fit behind the 16" Columba's :mad:

I think they go behind the Perfo's though :confused:

Id stick with genuine volvo disks and get some decent pads , maybe DS2500's...

hlm offer a fixing service think its about 120 quid. there is a seller on ebay too that does fixes for about 80 although I think they have accepted best offers of 60. there are tutorials on how to...

AH yes, you can see it now.

There looks to be another bracket/piece of flat under the new bracket on yours Rob.

I think looking at the pics that you've gotten slightly confused by the fitting kit. In the kit there where two flat metal pieces, I think you've put them under the bracket and attached them using...

Hey Rob,
I'm not too far from you, so if you need a hand with things like that, just pm me...thats what these club are for...aren't they?

Unless his car doesn't have the original bits on the boot, like my first one didn't.
Some cars have 4 bits of bracket, some only have the 2.

You see i told you didnt i :B_thumb:

Enjoy matey

Hi Rob

Start with the cap itself :B_thumb:

Less than £10 delivered ( £9.18 ) for a new one :D

http://www.partsforvolvosonline.com/product_info.php?products_id=4737

I worked for a Scooby dealer from 2000 - 2002.
The first standard UK Impreza turbo's were 208 bhp iirc and then the later turbo 2000 ones, up to 51 plate, were 218 bhp? You could do a Prodrive...

The strut brace mentioned above (which cost me £70) gave me the biggest single imrovement in body roll....

Springs help as well, but when I added the brace, the difference in roll was noticable...

Shocks and springs first, if you are going for springs you might as well get new shocks put in while you are there. Bilstein Sport shocks or a good branded replacement shock build for lowering...

Lowering springs I would say first. Kilen lowering kit part number 968428. This will be 40mm lower. There about £90.00 plus vat from most motor factors.

They look very good indeed. Well done buddy. Too late for me I bought new V70 ones. I tryed all sorts on mine (except wot you did) and found they looked great for afew weeks or untill it pi**ed down...

yeh deffo 8mm bolts careful you don't drop the spanner down the D pillar like my nephew did, it takes a while to get at em..... :doh:

and not contradicting, but I took my top parts only off both...

hi,
remove the covers,then inside you will see nuts to remove the light units.
cant remember if they are 8mm nuts or 10mm.think its 8mm lol.
careful as you remove them cos the estate light units...

lee get the 304 wrote where you have the ??????? on your pic lol