don kalmar union
Trader
Find latest postsMini Statistics
- Join Date
- Tuesday 20th August 2013
- Last Activity
- Yesterday 19:12
- Tab Content
-
Older Activity
-
Yesterday, 09:48Bill, you could try removing the calipers and giving them a real good clean first. Carefully squeeze the pistons out (not all the way) and make sure...9 replies | 154 view(s)
-
Saturday 16th February 2019, 21:31Oh dear. That's gonna cost you then. £435 each from Volvo and they are exchange only.9 replies | 154 view(s)
-
Saturday 16th February 2019, 10:14I normally use a thermo probe. Highly accurate and an immediate answer! Just aim it at the disc surface and compare to the opposite side. They should...9 replies | 154 view(s)
-
Saturday 16th February 2019, 10:11God I'm good :o That's another bacon roll and a coffee you owe me! ;) Did you keep those calipers that I advised you to keep?9 replies | 154 view(s)
-
Monday 11th February 2019, 21:04It means take the car to a gearbox specialist for a confirmed diagnosis and in the mean time, avoid wide open throttle and high load conditions or...4 replies | 93 view(s)
-
Monday 11th February 2019, 20:561. Check the calipers are not slightly binding. 2. Propshaft CV's. 3. Driveshafts inners / outers excess play. 4. Wheel alignment can also cause...9 replies | 154 view(s)
-
Monday 11th February 2019, 08:40Sounds to me like your auto box is slipping. Oh dear :(4 replies | 93 view(s)
-
Monday 11th February 2019, 08:37What makes you think the studs broken? They nearly always work loose, especially on cylinder 1 and 2. Just carefully tighten them back up, but...8 replies | 169 view(s)
-
Tuesday 5th February 2019, 04:42You'll need to with that mileage! Last recorded at 308,172 on 01/03/2018.2 replies | 182 view(s)
-
Tuesday 5th February 2019, 04:31Mmmm, incorrect FP would store a FP fault code anyway, so I assume this was ok? A blocked fuel filter would normally store a P0089 fault code and as...5 replies | 211 view(s)
-
Tuesday 5th February 2019, 04:03Hi Chris. The first place I would look is VIDA and any fault codes, especially in relation to CANbus issues with no comms for the ECM (Engine...5 replies | 211 view(s)
-
Sunday 3rd February 2019, 19:15They don't self heal, as you say, but the coil windings which are made of copper do get very hot. Consequently, the copper strands break. On rare...5 replies | 229 view(s)
-
Wednesday 30th January 2019, 16:09The copper coil winding inside the coil breaks / open circuit and you lose the spark. This usually occurs when hot and under load, but can also occur...5 replies | 229 view(s)
2 Visitor Messages
About don kalmar union
Basic Information
About don kalmar union
- Location:
- Chesham, Bucks.
Signature
MTE performance software, Ferrita stainless exhausts, TME stainless exhausts, AP heavy duty clutch kits, KU single mass flywheels and LSDs. 01494 785508. email don@kalmar-union.com
www.kalmar-union.com
www.kalmar-union.com
Statistics
Total Posts
- Total Posts
- 254
- Posts Per Day
- 0.13
Visitor Messages
- Total Messages
- 2
- Most Recent Message
- Monday 15th May 2017 14:35
Total Thanks
- Total Thanks
- 6
- Thanked 173 Times in 97 Posts
- Find all thanked posts by don kalmar union
- Find all posts thanked by don kalmar union
General Information
- Last Activity
- Yesterday 19:12
- Join Date
- Tuesday 20th August 2013
- Referrals
- 2
No results to display...
| iTrader Profile | Recent Ratings | ||||||||||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||||||||||
