Yet Again the C70 has me Pulling Hair Out

[c70geoff]

As per the title i'm loosing faith with this car, but I will not let it beat me
I had all the intention of finally sorting out my lowering springs today but on the way to my mates garage a nice little whinning noise started from the front. so I slowed down and gently continued to destination where we jacked up the drivers side to find my wheel bearing was pretty much shot.
One quick phone call to a local stockist and £57 later a new bearing unit turned up. Lots of swear words and broken nuts and bolts later and some serious energy drink downing we finally got the offending units changed. Then came the drive home which started off great until I started hearing a clunking noise. So i pulled over just to check my wheel nuts which where ok and as I was no where near the garage I decided to slowly get home. then when braking that lovely pedal bounce and grinding noise started again. which I know is the abs ring I didn't fit months ago.
Once home I checked to see if I hadn't tightened a bolt or something to find them all good and the bottom ball joint §§§§§§ed.
gotta try get a new wishbone in morning now so forgive me for this
AAAAAAAAAAAAAAAAAAAAAARRRRRRRRRRRRRRRRRRRRRRRRRRRR RRRRRRGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG GGGGGGGGGGHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHH

Ah thats better

[JamesT5]

As per the title i'm loosing faith with this car, but I will not let it beat me
I had all the intention of finally sorting out my lowering springs today but on the way to my mates garage a nice little whinning noise started from the front. so I slowed down and gently continued to destination where we jacked up the drivers side to find my wheel bearing was pretty much shot.
One quick phone call to a local stockist and £57 later a new bearing unit turned up. Lots of swear words and broken nuts and bolts later and some serious energy drink downing we finally got the offending units changed. Then came the drive home which started off great until I started hearing a clunking noise. So i pulled over just to check my wheel nuts which where ok and as I was no where near the garage I decided to slowly get home. then when braking that lovely pedal bounce and grinding noise started again. which I know is the abs ring I didn't fit months ago.
Once home I checked to see if I hadn't tightened a bolt or something to find them all good and the bottom ball joint §§§§§§ed.
gotta try get a new wishbone in morning now so forgive me for this
AAAAAAAAAAAAAAAAAAAAAARRRRRRRRRRRRRRRRRRRRRRRRRRRR RRRRRRGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG GGGGGGGGGGHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHH

Ah thats better

I know how this feels! You get one problem sorted out and then you spot 6 dozen other things that are knackered, so you fix them and then something else goes wrong. Very annoying and something I can totally relate to!

[stribo]

As per the title i'm loosing faith with this car, but I will not let it beat me
I had all the intention of finally sorting out my lowering springs today but on the way to my mates garage a nice little whinning noise started from the front. so I slowed down and gently continued to destination where we jacked up the drivers side to find my wheel bearing was pretty much shot.
One quick phone call to a local stockist and £57 later a new bearing unit turned up. Lots of swear words and broken nuts and bolts later and some serious energy drink downing we finally got the offending units changed. Then came the drive home which started off great until I started hearing a clunking noise. So i pulled over just to check my wheel nuts which where ok and as I was no where near the garage I decided to slowly get home. then when braking that lovely pedal bounce and grinding noise started again. which I know is the abs ring I didn't fit months ago.
Once home I checked to see if I hadn't tightened a bolt or something to find them all good and the bottom ball joint §§§§§§ed.
gotta try get a new wishbone in morning now so forgive me for this
AAAAAAAAAAAAAAAAAAAAAARRRRRRRRRRRRRRRRRRRRRRRRRRRR RRRRRRGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG GGGGGGGGGGHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHH

Ah thats better

My n/s/f (I think) wheel bearing's been whining since I bought it last July, but there's no play in the wheel, which is why I said I think it's n/s/f. It's something I'l do at some point, but Not urgent as far as I'm concerned (famous last words lol). How difficult was yours to replace?

[M-R-P]

Bummer mate.
Sometimes you can't spot/replace/fix something before it lets - go. Ball joints and bearings are one of those things :(

[c70geoff]

Its not that hard a job to do just gotta watch the 4 bolts that hold the bearing unit into the hub dont snap. I heated mine a little before i even attempted to loosen them. apart from that was straight forward. no pressing in bearing needed as its a complete unit

http://i17.photobucket.com/albums/b81/miragecoupe/9C575B80-5686-4208-8F52-8F2B8C8086B0-3172-00000274FDA28491_zpsc518d137.jpg
http://i17.photobucket.com/albums/b81/miragecoupe/49D3106D-4607-426D-9C57-0037BB1F0D62-3172-00000275075354F1_zps7d383f48.jpg

Geoof 1, wheel bearing 0

[V70 Graham]

Hard luck mate, just when you thought you'd cracked it, there's always something else ready to surprise you. Hope you get sorted in the morning without too much of a ball ache !

[c70geoff]

cheers Graham
I am not letting it beat me hahahahahahaha

[stribo]

Its not that hard a job to do just gotta watch the 4 bolts that hold the bearing unit into the hub dont snap. I heated mine a little before i even attempted to loosen them. apart from that was straight forward. no pressing in bearing needed as its a complete unit

http://i17.photobucket.com/albums/b81/miragecoupe/9C575B80-5686-4208-8F52-8F2B8C8086B0-3172-00000274FDA28491_zpsc518d137.jpg
http://i17.photobucket.com/albums/b81/miragecoupe/49D3106D-4607-426D-9C57-0037BB1F0D62-3172-00000275075354F1_zps7d383f48.jpg

Geoof 1, wheel bearing 0

How did you get it off the driveshaft?

[JamesT5]

How did you get it off the driveshaft?

I hate splines!

[c70geoff]

there is a 15mm bolt in the centre opening of the bearing that goes into the end of the shaft mate, take it out and the shaft should put gently out

[JamesT5]

Its not that hard a job to do just gotta watch the 4 bolts that hold the bearing unit into the hub dont snap. I heated mine a little before i even attempted to loosen them. apart from that was straight forward. no pressing in bearing needed as its a complete unit

http://i17.photobucket.com/albums/b81/miragecoupe/9C575B80-5686-4208-8F52-8F2B8C8086B0-3172-00000274FDA28491_zpsc518d137.jpg
http://i17.photobucket.com/albums/b81/miragecoupe/49D3106D-4607-426D-9C57-0037BB1F0D62-3172-00000275075354F1_zps7d383f48.jpg

Geoof 1, wheel bearing 0

By the way, I don't see much hair on the floor. :D

[c70geoff]

lol theres a bin for that
well on a better note wishbone with ball joint fitted £35 from local motor factors....yay

[stribo]

lol theres a bin for that
well on a better note wishbone with ball joint fitted £35 from local motor factors....yay

Have you got the 4 bolt wishbones? as that sounds a really good price. Do you have a link?

[c70geoff]

2 bolt on mine mate and the motor factors are fast parts

http://www.fastpartswales.co.uk/

[stribo]

2 bolt on mine mate and the motor factors are fast parts

http://www.fastpartswales.co.uk/

Oh right, yeah the 2 bolt ones are quite a bit cheaper, I've got 4 bolt ones. :(

[c70geoff]

dont think there was a huge difference in price fella

[stribo]

dont think there was a huge difference in price fella

I'll give them a ring Monday.

[c70geoff]

don't bother ringing fella
according to there database mine was 2 bolt but when all came off was a 4 bolt(i know shoulda checked first)
so went back and price is nearly 3 times the amount....thinking of changing my local motor factors as these guys are starting to be rather poo